ARES Plate Heat Exchanger2023-11-17T17:20:42+08:00

Malaysia’s Exclusive Distributor of ARES Plate Heat Exchangers

The ARES Plate heat exchanger (PHE) is a type of heat exchanger that uses metal plates sealed with gaskets to transfer heat between a hot fluid and a cold fluid. It consists of a frame, which consists of a front cover, rear (movable) parts, carrying bar, guiding bar, and a number of tie bolts depending on the type of the plate heat exchanger.

The heat is transferred from one medium to another through plates, which have been pressed. The hot and cold medium flows through between each of the plates and then they exchange their heat without mixing each other.

Liquid flowing through the PHE channels experience turbulent flow at low velocities producing high heat transfer efficiency and low fouling which results in smaller and a compact unit. A PHE has wide industrial applications especially in HVAC, oil and gas, power generation, edible oil etc.

Plate Heat Exchanger Structure

Plate Structure

The heat transfer plates are mainly produced from SS304, SS316, SMO, Hastelloy or Titanium material, 0.5 mm – 1 mm plate sheets. In general, there are two types of plate for each model which are thermally long and thermally short plates. The difference between them is that the wide and narrow angle on the herringbone pattern.

Thermally Long Plates:

  • High turbulence output
  • Close temperature approach (LMTD: 1°C)
  • High pressure loss

Thermally Short Plates:

  • Low turbulence output
  • Low heat transfer value
  • Low pressure loss

Gasket Types

Gaskets are among most critical element of the plate heat exchanger. Depending on the temperature and fluid type the material of the gaskets may vary. The most common type of gaskets are NBR and EPDM gaskets. For different applications there are other specific types of gaskets such as Viton and Silicone. The contamination or mixing of the two fluids are prevented by using the following gaskets system. Only one side of the gasket has contact with the fluid and the other side has contact with the atmosphere. Therefore, in any case of leakage the fluid runs outside of the plate heat exchanger rather than mixing with the other fluid.

Gasket TypeMaximum Working Temperature
NBR120 °C – 140 °C
EPDM140 °C – 160 °C
Viton180 °C – 200 °C

Contact us to find out more

PHE Series

AWG Series – Wide Gap Plates

AWG Series consists of only wide gap plates. Compare to A Series plates, AWG plates have 5.5 mm to 12 mm plate gap which makes them easier to use in applications where contamination in the fluid is high.

ASW Series – Semi Welded Plates

A cassette contains two plates laser welded together. The advantage of this method is; one side has a welded plate channel and the other side has a traditional plate channel with gaskets. On the welded side, there are two specially produced corner hole gaskets creating the sealing between two cassettes. Thus, the gasket exposure to the fluid is reduced to a minimum on welded side.

ADP Series – Double Wall Plates

Two plates lair-welded together to ensure safety. For applications such as pharmaceutical industry, food & beverage, district heating, cooling of transformer oil, etc, where it is crucial that medium are not mixed.


What are the components in a plate heat exchanger?2021-05-27T07:24:59+08:00

A plate heat exchanger unit consists of frame, carry bar, supporting bar, tightening rod and bolts, plates and gaskets.

How long does the plate heat exchanger last?2021-05-27T07:22:00+08:00

The lifespan of a plate heat exchanger is around 10 years in full working order and could be longer if maintenance is properly and regularly conducted. 

Do I need to clean my heat exchanger?2021-05-27T07:20:19+08:00

Like all mechanical equipment, heat exchangers require a regimen of regular maintenance. Fouling and corrosion are two of the common causes of performance degradation. The common practice of cleaning the heat exchanger is by rinsing, chemical cleaning, and changing the plates’ gasket if deem necessary.

Where are plates heat exchanger used?2021-05-27T07:23:57+08:00

Plate heat exchangers are used in applications where liquid heating or cooling is required. They are used in various working application such as textile industries, food and beverages industries, steel industries and surface treatment. They’re also used for economizer circuits and heat recovery circuits to reduce the cooling load on the chillers.

How does a plate heat exchanger work?2021-05-27T07:17:37+08:00

Plate heat exchanger consist of a series of parallel plates that are placed one above the other to allow the formation of a series of channels for fluids to flow between them. The heat exchanger consists of four channels which are cold side inlet and outlet and hot side inlet and outlet. The fluid flows from the inlet from both hot and cold side and the movement of the fluids will increase its temperature on the cold side and reduce in temperature in the hot side.

What is a plate heat exchanger?2021-05-27T06:59:39+08:00

A plate heat exchanger is a type of heat exchanger that uses metal plates to transfer heat between two fluids. Basically, the heat is transfer between two plates which would make the liquids increase and reduce in temperature.

Plate Heat Exchanger Models

ModelNozzle (mm)Flow (max.m3/hr)(H)(W)(L)
A1S25/3215460180485 – 885
A1L25/3215850180485 – 885
A2S5050694300655 – 1755
A2M5050994300655 – 1755
A2L50501194300655 – 1755
A3S65110626395443 – 1043


65110946395438 – 1038
A3L651101296395443 – 1043
A4S1001651441480700 – 4100
A4M1001651155480710 – 2110
A4A1001651715480710 – 2110
A6S1503802165480710 – 2110
A6M15038015126081122 – 4120
A6L15038019336081122 – 4120
A8M20065023366081122 – 4120
A8L20065027926081122 – 4120
A12M30015501506608677 – 4077
A12L30015501506608677 – 4077
A16M400300027926081122 – 4120
A20M50040001506608677 – 4077


Get A Quote Today

Go to Top